Sim2 C3X Lumis Manual de instalación descargar pdf (Pagina 21)

C3X Lumis

ENGLISH

REMOTE CONTROL - SPECIAL KEYS

MEMORIES

The main image parameters can be saved in separate sets of

values (called MEMORIES) so that they can be subsequently

applied as a group using a single command.

There are 6 separate Memories (Memory 1, Memory

2... -6) for each of the 6 signal types handled. The following

image parameters can be saved/recalled by the Memory

Management system:

Some of these parameters may not be available for certain in-

puts or certain input signals, as indicated in Tables 4 and 5.

The Memory Management function menu page is activated

by pressing the key on the remote control.

SAVING A MEMORY

To save the current values of the image parameters in

Memory 1, place yourself on line ‘1’ using keys ▼ and ▲‚

and open the pull-down menu with key ● (“enter” key on

the remote control). Select the “Save initial settings” line.

In conﬁrmation that the operation has been completed, on

the bottom there are the words “Current settings saved

in Memory 1”. Repeat the operation to save other image

settings in new memories.

USING A MEMORY

To use a Memory, select the line in question and press the

key. The settings stored in the memory you have selected

will be applied to the projected image, while a message

will conﬁrm that Memory has been applied.

The memory will be associated with the particular source

and signal type and will be automatically applied whenever

that particular combination of source and signal type is

selected.

SAVING ORIGINAL SETTINGS

To re-insert the values in a previously modiﬁed Memory,

select the line relative to such Memory and open the pull-

down menu corresponding with key ● (“enter” key on

the remote control).

Then select the “Save initial settings” line. The message,

“Initial settings saving in Memory 1” will be shown at

the bottom of the display to conﬁrm that the operation

has been completed.

RENAMING A MEMORY

All Memories can be named. To assign a name (with a

maximum length of 12 alphanumeric characters) to a

Memory, select the Rename option from the correspond-

ing pull-down menu.

Text is entered according to the procedure shown in the

section ENTERING TEXT.

RESTORING CURRENT SETTINGS

On entering menu MEMORIES a copy of the current set-

tings is saved in a temporary memory (marked 0 - AUTO).

Having recalled one or more memories, it is possible to

recover the existing settings at the time of entering menu

MEMORIES by selection Memory ‘0’ (0 - AUTO). Nonethe-

less, this operation must be carried out before the menu

page MEMORIES disappears (30 seconds after the last

operation with the remote control or keypad).

The next time it appears, in fact, the temporary memory

will contain new information which consider the Memories

eventually selected in the penultimate access to the page

MEMORIES.

Memory 0 can be used even when you do not wish to

enable Memories management for the signal in use. In

fact, once Memory 0 has been selected, when a source

is chosen, the settings that were effective at the time the

Memory was previously recalled will be automatically

applied.

Image Picture

BRIGHTNESS ASPECT

CONTRAST COLOUR TEMPERATURE

COLOUR OVERSCAN

SHARPNESS GAMMA CORRECTION

SHARPNESS MODE

FILTER

NOISE REDUCTION

0 Auto

MEMORY 1

MEMORIA 1

MEMORIA 2

MEMORIA 3

MEMORIA 4

MEMORY 5

MEMORY 6

Entra nel sottomenù

Elemento successivo

Menù successivo

Menù precedente

Esci dal menù

Memories

Save Memory

Save Initial Setting

Rename

0 Auto

MEMORY 1

MEMORY 2

MEMORY 3

MEMORY 4

MEMORY 5

MEMORY 6

Entra nel sottomenù

Elemento successivo

Menù successivo

Menù precedente

Esci dal menù

Memories

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 30 31

Comentarios a estos manuales

Sin comentarios

Sim2 C3X Lumis Manual de instalación Pagina 21

Comentarios a estos manuales

Relacionado con productos y manuales para Proyectores de datos Sim2 C3X Lumis