Sim2 C3X Lumis Manual de instalación descargar pdf (Pagina 23)

C3X Lumis

ENGLISH

GRAPHIC IMAGE WITH POOR QUALITY VERTICAL

DETAIL

• Check compatibility of the video or graphic signals

with the technical speciﬁcations of the projector, and in

particular, with the speciﬁcations of the selected input.

• Press key A on the remote control or ◀ on the projector

keypad to execute automatic adjustments.

• Adjust the FREQUENCY and PHASE settings in the IM-

AGE menu to optimise the vertical details of the image

(if available for the input in question).

VIDEO IMAGE WITH DETAILS NOT ALIGNED WITH

VERTICAL EDGES

• Check compatibility of the video or graphic signals

with the technical speciﬁcations of the system, and in

particular, with the speciﬁcations of the selected input.

• Adjust Y/C DELAY settings in the IMAGE menu to reduce

colour misalignment.

REMOTE CONTROL DOES NOT WORK

• Check remote control battery power and that they are

inserted correctly.

• Ensure the area between the infrared sensors (on the

front panel of the projector) and the remote control is

free from obstructions.

• Make sure the infrared sensors on the front and rear

of the projector are not exposed to very bright light

levels.

You can purchase the following optional accessories at your

Dealer:

1. Ceiling assembling kit for C3X LUMIS

2. Motorised brackets for Anamorphic Lens.

3. Anamorphic Lens

4. Infrared signal repeater

A range of lenses are available from our dealers to satisfy

varying installation and projection distance needs. See the

Additional Information chapter for further details on projection

distance and enlargement ratios. Always contact our service

centre to have the lens replaced. Use only original or SIM2

Multimedia approved accessories.

CAUTION: for ceiling installation using a suspension

bracket, follow the instructions meticulously and the

safety norms included in the bracket packaging.

12 OPTIONAL ACCESSORIES

• Check the state of the connection by interpreting the

code displayed by the projector LEDs.

• Make sure the cooling air vents on the units are not

blocked and that the room temperature is below

35°C.

IMAGE IS DISTURBED, UNSTABLE OR NOISY

• Check compatibility of the video or graphic signals with

the technical speciﬁcations of the projector, and speciﬁ-

cally, with the speciﬁcations of the selected input.

• Check all cables.

• If the problem occurs on a terrestrial broadcast source

signal, check that the receiver has been correctly tuned

in and that the aerial system is in good working order.

• Adjust the Sharpness parameter in the PICTURE menu

to optimise the projected image.

• If you are using a Blue-Ray or HDVD high-deﬁnition disk

player, consider that the material recorded on the disk

may be coded with a frame rate of 1080p 24Hz, which

is the same format shown at the movies. Often the ﬁlm

previews, screen notices, menus and special sections

are recorded at a different frequency than the main

section, such as 1080i 25/30Hz, etc.

• For this reason, depending on how the player is set, the

projector will appear to be “searching” for the correct

signal and sometimes it will display “No signal” while

the player is synchronizing on the correct format. On

these occasions, a few seconds of the beginning of the

program may not be displayed while the projector is

stabilizing. This is normal and should not be considered

as a malfunction.

INCOMPLETE IMAGE AT EDGES

• Check compatibility of the video or graphic signals

with the technical speciﬁcations of the projector, and in

particular, with the speciﬁcations of the selected input.

• Open the automatic image adjustment function by

pressing the key A on the remote control or ◀ on the

projector’s keypad.

• Adjust the horizontal or vertical position of the image with

the IMAGE/POSITION menu (if available for the input in

question).

• Adjust the image width and height, selecting Aspect in

the IMAGE /ASPECT menu.

• Adjust the overscan setting applied to the image on the

IMAGE/OVERSCAN menu.

IMAGE TOO DARK/PALE OR UNNATURALLY COL-

OURED

• Check compatibility of the video or graphic signals

with the technical speciﬁcations of the projector, and in

particular, with the speciﬁcations of the selected input.

• Adjust the CONTRAST, BRIGHTNESS, COLOUR and

TINT parameters in the PICTURE menu.

• If necessary, adjust COLOUR TEMPERATURE and

GAMMA CORRECTION (IMAGE menu).

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 29 30 31

Comentarios a estos manuales

Sin comentarios

Sim2 C3X Lumis Manual de instalación Pagina 23

Comentarios a estos manuales

Relacionado con productos y manuales para Proyectores de datos Sim2 C3X Lumis